瑞芯微支持的摄像头，有个support list，
此次从该list中选择了IMX415
RK提供的默认sdk里面已经将支持的所有摄像头驱动都添加到了内核，所以不需要移植该驱动了。
需确认下移植驱动对应的一些信息
3588_linux/3588_linux5.10_v1.0.5/kernel/drivers/media/i2c/imx415.c 3588_linux/3588_linux5.10_v1.0.5/kernel/drivers/media/i2c/Makefile 3588_linux/3588_linux5.10_v1.0.5/kernel/drivers/media/i2c/Kconfig 3588_linux/3588_linux5.10_v1.0.5/kernel/arch/arm64/configs/rockchip_linxu_defconfig
obj-$(CONFIG_VIDEO_IMX415) += imx415.o
config VIDEO_IMX415
tristate "Sony IMX415 sensor support"
depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
depends on MEDIA_CAMERA_SUPPORT
help
This is a Video4Linux2 sensor driver for the Sony
IMX415 camera.
To compile this driver as a module, choose M here: the
module will be called imx415.
CONFIG_VIDEO_IMX415=y
1）摄像头链接示意图
IMX415摄像头与SOC连接的主要的引脚有：i2c、rst、pwdn、mclk、MIPI Clk、MIPI DATA
2）电路图
由电路图可知，几个关键引脚关系：
reset信号：gpio4 A0
power0 down信号：gpio1 B0
I2C通道：3
clock：CLK_MIPI_CAMARAOUT_M3
3）设备树节点
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2022 Rockchip Electronics Co., Ltd.
*
*/
/ {
compatible = "radxa,rock-5b", "rockchip,rk3588";
camera_pwdn_gpio: camera-pwdn-gpio {
status = "okay";
compatible = "regulator-fixed";
regulator-name = "camera_pwdn_gpio";
regulator-always-on;
regulator-boot-on;
enable-active-high;
gpio = <&gpio1 RK_PB0 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&cam_pwdn_gpio>;
};
clk_cam_24m: external-camera-clock-24m {
status = "okay";
compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "clk_cam_24m";
#clock-cells = <0>;
};
};
&i2c3 {
status = "okay";
imx415: imx415@1a {
status = "okay";
compatible = "sony,imx415";
reg = <0x1a>;
clocks = <&cru CLK_MIPI_CAMARAOUT_M3>;
clock-names = "xvclk";
pinctrl-names = "default";
pinctrl-0 = <&mipim0_camera3_clk>;
power-domains = <&power RK3588_PD_VI>;
pwdn-gpios = <&gpio1 RK_PB0 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio4 RK_PA0 GPIO_ACTIVE_LOW>;
rockchip,camera-module-index = <0>;
rockchip,camera-module-facing = "back";
rockchip,camera-module-name = "CMK-OT2022-PX1";
rockchip,camera-module-lens-name = "IR0147-50IRC-8M-F20";
port {
imx415_out0: endpoint {
remote-endpoint = <&mipidphy0_in_ucam0>;
data-lanes = <1 2 3 4>;
};
};
};
camera_imx219: camera-imx219@10 {
status = "disabled";
compatible = "sony,imx219";
reg = <0x10>;
clocks = <&clk_cam_24m>;
clock-names = "xvclk";
rockchip,camera-module-index = <0>;
rockchip,camera-module-facing = "back";
rockchip,camera-module-name = "rpi-camera-v2";
rockchip,camera-module-lens-name = "default";
port {
imx219_out0: endpoint {
remote-endpoint = <&mipidphy0_in_ucam1>;
data-lanes = <1 2>;
};
};
};
};
&csi2_dphy0_hw {
status = "okay";
};
&csi2_dphy0 {
status = "okay";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
mipidphy0_in_ucam0: endpoint@1 {
reg = <1>;
remote-endpoint = <&imx415_out0>;
data-lanes = <1 2 3 4>;
};
mipidphy0_in_ucam1: endpoint@2 {
reg = <2>;
remote-endpoint = <&imx219_out0>;
data-lanes = <1 2>;
};
};
port@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
csidphy0_out: endpoint@0 {
reg = <0>;
remote-endpoint = <&mipi2_csi2_input>;
};
};
};
};
&mipi2_csi2 {
status = "okay";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
mipi2_csi2_input: endpoint@1 {
reg = <1>;
remote-endpoint = <&csidphy0_out>;
};
};
port@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
mipi2_csi2_output: endpoint@0 {
reg = <0>;
remote-endpoint = <&cif_mipi2_in0>;
};
};
};
};
&rkcif {
status = "okay";
};
&rkcif_mipi_lvds2 {
status = "okay";
port {
cif_mipi2_in0: endpoint {
remote-endpoint = <&mipi2_csi2_output>;
};
};
};
&rkcif_mipi_lvds2_sditf {
status = "okay";
port {
mipi_lvds2_sditf: endpoint {
remote-endpoint = <&isp0_vir0>;
};
};
};
&rkcif_mmu {
status = "okay";
};
&rkisp0 {
status = "okay";
};
&isp0_mmu {
status = "okay";
};
&rkisp0_vir0 {
status = "okay";
port {
#address-cells = <1>;
#size-cells = <0>;
isp0_vir0: endpoint@0 {
reg = <0>;
remote-endpoint = <&mipi_lvds2_sditf>;
};
};
};
&pinctrl {
camera {
cam_pwdn_gpio: cam-pwdn-gpio {
rockchip,pins = <1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
};
设备树的信息最终转换成i2c_client,并传递给IMX415驱动 imx415_probe(){ compatible = “imx415”;与驱动的 of_match_table 保持一致
rockchip,camera-module-index = <0>;
rockchip,camera-module-facing = "back";
rockchip,camera-module-name = "CMK-OT2022-PX1";
rockchip,camera-module-lens-name = "IR0147-50IRC-8M-F20";
匹配的是external\camera_engine_rkaiq\iqfiles\isp3x下面的iq文件
root@linaro-alip:/# dmesg | grep imx415
[ 2.547754] imx415 3-001a: driver version: 00.01.08
[ 2.547767] imx415 3-001a: Get hdr mode failed! no hdr default
[ 2.547819] imx415 3-001a: Failed to get power-gpios
[ 2.547826] imx415 3-001a: could not get default pinstate
[ 2.547831] imx415 3-001a: could not get sleep pinstate
[ 2.547850] imx415 3-001a: supply dvdd not found, using dummy regulator
[ 2.547918] imx415 3-001a: supply dovdd not found, using dummy regulator
[ 2.547945] imx415 3-001a: supply avdd not found, using dummy regulator
[ 2.613843] imx415 3-001a: Detected imx415 id 0000e0
[ 2.613890] rockchip-csi2-dphy csi2-dphy0: dphy0 matches m00_b_imx415 3-001a:bus type 5
[ 18.386174] imx415 3-001a: set fmt: cur_mode: 3864x2192, hdr: 0
[ 18.389067] imx415 3-001a: set exposure(shr0) 2047 = cur_vts(2250) - val(203)
驱动加载成功后，会有以下信息
root@linaro-alip:/rockchip-test# ls /dev/video* -l
crw-rw----+ 1 root video 81, 0 8月 7 15:26 /dev/video0
crw-rw----+ 1 root video 81, 1 8月 7 15:26 /dev/video1
crw-rw----+ 1 root video 81, 10 8月 7 15:26 /dev/video10
crw-rw----+ 1 root video 81, 11 8月 7 15:26 /dev/video11
crw-rw----+ 1 root video 81, 12 8月 7 15:26 /dev/video12
crw-rw----+ 1 root video 81, 13 8月 7 15:26 /dev/video13
crw-rw----+ 1 root video 81, 14 8月 7 15:26 /dev/video14
crw-rw----+ 1 root video 81, 15 8月 7 15:26 /dev/video15
crw-rw----+ 1 root video 81, 16 8月 7 15:26 /dev/video16
crw-rw----+ 1 root video 81, 17 8月 7 15:26 /dev/video17
crw-rw----+ 1 root video 81, 18 8月 7 15:26 /dev/video18
crw-rw----+ 1 root video 81, 19 8月 7 15:26 /dev/video19
crw-rw----+ 1 root video 81, 2 8月 7 15:26 /dev/video2
crw-rw----+ 1 root video 81, 20 8月 7 15:26 /dev/video20
crw-rw----+ 1 root video 81, 3 8月 7 15:26 /dev/video3
crw-rw----+ 1 root video 81, 4 8月 7 15:26 /dev/video4
crw-rw----+ 1 root video 81, 5 8月 7 15:26 /dev/video5
crw-rw----+ 1 root video 81, 6 8月 7 15:26 /dev/video6
crw-rw----+ 1 root video 81, 7 8月 7 15:26 /dev/video7
crw-rw----+ 1 root video 81, 8 8月 7 15:26 /dev/video8
crw-rw----+ 1 root video 81, 9 8月 7 15:26 /dev/video9
lrwxrwxrwx 1 root root 7 8月 7 15:26 /dev/video-camera0 -> video11
-rw-rw---- 1 root video 4 8月 7 15:26 /dev/video-dec0
-rw-rw---- 1 root video 4 8月 7 15:26 /dev/video-enc0
内核会为摄像头在目录/sys/class/video4linux下分配设备信息描述文件
root@linaro-alip:grep imx415 /sys/class/video4linux/v*/name
root@linaro-alip:/rockchip-test# grep imx415 /sys/class/video4linux/v*/name
/sys/class/video4linux/v4l-subdev2/name:m00_b_imx415 3-001a
root@linaro-alip:/rockchip-test# grep "" /sys/class/video4linux/v*/name | grep mainpath
/sys/class/video4linux/video11/name:rkisp_mainpath
root@linaro-alip:/rockchip-test# media-ctl -d /dev/media0 -p
Media controller API version 5.10.110
Media device information
------------------------
driver rkcif
model rkcif-mipi-lvds2
serial
bus info
hw revision 0x0
driver version 5.10.110
Device topology
- entity 1: stream_cif_mipi_id0 (1 pad, 11 links)
type Node subtype V4L flags 0
device node name /dev/video0
pad0: Sink
<- "rockchip-mipi-csi2":1 [ENABLED]
<- "rockchip-mipi-csi2":2 []
<- "rockchip-mipi-csi2":3 []
<- "rockchip-mipi-csi2":4 []
<- "rockchip-mipi-csi2":5 []
<- "rockchip-mipi-csi2":6 []
<- "rockchip-mipi-csi2":7 []
<- "rockchip-mipi-csi2":8 []
<- "rockchip-mipi-csi2":9 []
<- "rockchip-mipi-csi2":10 []
<- "rockchip-mipi-csi2":11 []
- entity 5: stream_cif_mipi_id1 (1 pad, 11 links)
type Node subtype V4L flags 0
device node name /dev/video1
pad0: Sink
<- "rockchip-mipi-csi2":1 []
<- "rockchip-mipi-csi2":2 [ENABLED]
<- "rockchip-mipi-csi2":3 []
<- "rockchip-mipi-csi2":4 []
<- "rockchip-mipi-csi2":5 []
<- "rockchip-mipi-csi2":6 []
<- "rockchip-mipi-csi2":7 []
<- "rockchip-mipi-csi2":8 []
<- "rockchip-mipi-csi2":9 []
<- "rockchip-mipi-csi2":10 []
<- "rockchip-mipi-csi2":11 []
- entity 9: stream_cif_mipi_id2 (1 pad, 11 links)
type Node subtype V4L flags 0
device node name /dev/video2
pad0: Sink
<- "rockchip-mipi-csi2":1 []
<- "rockchip-mipi-csi2":2 []
<- "rockchip-mipi-csi2":3 [ENABLED]
<- "rockchip-mipi-csi2":4 []
<- "rockchip-mipi-csi2":5 []
<- "rockchip-mipi-csi2":6 []
<- "rockchip-mipi-csi2":7 []
<- "rockchip-mipi-csi2":8 []
<- "rockchip-mipi-csi2":9 []
<- "rockchip-mipi-csi2":10 []
<- "rockchip-mipi-csi2":11 []
- entity 13: stream_cif_mipi_id3 (1 pad, 11 links)
type Node subtype V4L flags 0
device node name /dev/video3
pad0: Sink
<- "rockchip-mipi-csi2":1 []
<- "rockchip-mipi-csi2":2 []
<- "rockchip-mipi-csi2":3 []
<- "rockchip-mipi-csi2":4 [ENABLED]
<- "rockchip-mipi-csi2":5 []
<- "rockchip-mipi-csi2":6 []
<- "rockchip-mipi-csi2":7 []
<- "rockchip-mipi-csi2":8 []
<- "rockchip-mipi-csi2":9 []
<- "rockchip-mipi-csi2":10 []
<- "rockchip-mipi-csi2":11 []
- entity 17: rkcif_scale_ch0 (1 pad, 11 links)
type Node subtype V4L flags 0
device node name /dev/video4
pad0: Sink
<- "rockchip-mipi-csi2":1 []
<- "rockchip-mipi-csi2":2 []
<- "rockchip-mipi-csi2":3 []
<- "rockchip-mipi-csi2":4 []
<- "rockchip-mipi-csi2":5 [ENABLED]
<- "rockchip-mipi-csi2":6 []
<- "rockchip-mipi-csi2":7 []
<- "rockchip-mipi-csi2":8 []
<- "rockchip-mipi-csi2":9 []
<- "rockchip-mipi-csi2":10 []
<- "rockchip-mipi-csi2":11 []
- entity 21: rkcif_scale_ch1 (1 pad, 11 links)
type Node subtype V4L flags 0
device node name /dev/video5
pad0: Sink
<- "rockchip-mipi-csi2":1 []
<- "rockchip-mipi-csi2":2 []
<- "rockchip-mipi-csi2":3 []
<- "rockchip-mipi-csi2":4 []
<- "rockchip-mipi-csi2":5 []
<- "rockchip-mipi-csi2":6 [ENABLED]
<- "rockchip-mipi-csi2":7 []
<- "rockchip-mipi-csi2":8 []
<- "rockchip-mipi-csi2":9 []
<- "rockchip-mipi-csi2":10 []
<- "rockchip-mipi-csi2":11 []
- entity 25: rkcif_scale_ch2 (1 pad, 11 links)
type Node subtype V4L flags 0
device node name /dev/video6
pad0: Sink
<- "rockchip-mipi-csi2":1 []
<- "rockchip-mipi-csi2":2 []
<- "rockchip-mipi-csi2":3 []
<- "rockchip-mipi-csi2":4 []
<- "rockchip-mipi-csi2":5 []
<- "rockchip-mipi-csi2":6 []
<- "rockchip-mipi-csi2":7 [ENABLED]
<- "rockchip-mipi-csi2":8 []
<- "rockchip-mipi-csi2":9 []
<- "rockchip-mipi-csi2":10 []
<- "rockchip-mipi-csi2":11 []
- entity 29: rkcif_scale_ch3 (1 pad, 11 links)
type Node subtype V4L flags 0
device node name /dev/video7
pad0: Sink
<- "rockchip-mipi-csi2":1 []
<- "rockchip-mipi-csi2":2 []
<- "rockchip-mipi-csi2":3 []
<- "rockchip-mipi-csi2":4 []
<- "rockchip-mipi-csi2":5 []
<- "rockchip-mipi-csi2":6 []
<- "rockchip-mipi-csi2":7 []
<- "rockchip-mipi-csi2":8 [ENABLED]
<- "rockchip-mipi-csi2":9 []
<- "rockchip-mipi-csi2":10 []
<- "rockchip-mipi-csi2":11 []
- entity 33: rkcif_tools_id0 (1 pad, 11 links)
type Node subtype V4L flags 0
device node name /dev/video8
pad0: Sink
<- "rockchip-mipi-csi2":1 []
<- "rockchip-mipi-csi2":2 []
<- "rockchip-mipi-csi2":3 []
<- "rockchip-mipi-csi2":4 []
<- "rockchip-mipi-csi2":5 []
<- "rockchip-mipi-csi2":6 []
<- "rockchip-mipi-csi2":7 []
<- "rockchip-mipi-csi2":8 []
<- "rockchip-mipi-csi2":9 [ENABLED]
<- "rockchip-mipi-csi2":10 []
<- "rockchip-mipi-csi2":11 []
- entity 37: rkcif_tools_id1 (1 pad, 11 links)
type Node subtype V4L flags 0
device node name /dev/video9
pad0: Sink
<- "rockchip-mipi-csi2":1 []
<- "rockchip-mipi-csi2":2 []
<- "rockchip-mipi-csi2":3 []
<- "rockchip-mipi-csi2":4 []
<- "rockchip-mipi-csi2":5 []
<- "rockchip-mipi-csi2":6 []
<- "rockchip-mipi-csi2":7 []
<- "rockchip-mipi-csi2":8 []
<- "rockchip-mipi-csi2":9 []
<- "rockchip-mipi-csi2":10 [ENABLED]
<- "rockchip-mipi-csi2":11 []
- entity 41: rkcif_tools_id2 (1 pad, 11 links)
type Node subtype V4L flags 0
device node name /dev/video10
pad0: Sink
<- "rockchip-mipi-csi2":1 []
<- "rockchip-mipi-csi2":2 []
<- "rockchip-mipi-csi2":3 []
<- "rockchip-mipi-csi2":4 []
<- "rockchip-mipi-csi2":5 []
<- "rockchip-mipi-csi2":6 []
<- "rockchip-mipi-csi2":7 []
<- "rockchip-mipi-csi2":8 []
<- "rockchip-mipi-csi2":9 []
<- "rockchip-mipi-csi2":10 []
<- "rockchip-mipi-csi2":11 [ENABLED]
- entity 45: rockchip-mipi-csi2 (12 pads, 122 links)
type V4L2 subdev subtype Unknown flags 0
device node name /dev/v4l-subdev0
pad0: Sink
[fmt:SGBRG10_1X10/3864x2192 field:none
crop.bounds:(12,16)/3840x2160
crop:(12,16)/3840x2160]
<- "rockchip-csi2-dphy0":1 [ENABLED]
pad1: Source
-> "stream_cif_mipi_id0":0 [ENABLED]
-> "stream_cif_mipi_id1":0 []
-> "stream_cif_mipi_id2":0 []
-> "stream_cif_mipi_id3":0 []
-> "rkcif_scale_ch0":0 []
-> "rkcif_scale_ch1":0 []
-> "rkcif_scale_ch2":0 []
-> "rkcif_scale_ch3":0 []
-> "rkcif_tools_id0":0 []
-> "rkcif_tools_id1":0 []
-> "rkcif_tools_id2":0 []
pad2: Source
-> "stream_cif_mipi_id0":0 []
-> "stream_cif_mipi_id1":0 [ENABLED]
-> "stream_cif_mipi_id2":0 []
-> "stream_cif_mipi_id3":0 []
-> "rkcif_scale_ch0":0 []
-> "rkcif_scale_ch1":0 []
-> "rkcif_scale_ch2":0 []
-> "rkcif_scale_ch3":0 []
-> "rkcif_tools_id0":0 []
-> "rkcif_tools_id1":0 []
-> "rkcif_tools_id2":0 []
pad3: Source
-> "stream_cif_mipi_id0":0 []
-> "stream_cif_mipi_id1":0 []
-> "stream_cif_mipi_id2":0 [ENABLED]
-> "stream_cif_mipi_id3":0 []
-> "rkcif_scale_ch0":0 []
-> "rkcif_scale_ch1":0 []
-> "rkcif_scale_ch2":0 []
-> "rkcif_scale_ch3":0 []
-> "rkcif_tools_id0":0 []
-> "rkcif_tools_id1":0 []
-> "rkcif_tools_id2":0 []
pad4: Source
-> "stream_cif_mipi_id0":0 []
-> "stream_cif_mipi_id1":0 []
-> "stream_cif_mipi_id2":0 []
-> "stream_cif_mipi_id3":0 [ENABLED]
-> "rkcif_scale_ch0":0 []
-> "rkcif_scale_ch1":0 []
-> "rkcif_scale_ch2":0 []
-> "rkcif_scale_ch3":0 []
-> "rkcif_tools_id0":0 []
-> "rkcif_tools_id1":0 []
-> "rkcif_tools_id2":0 []
pad5: Source
-> "stream_cif_mipi_id0":0 []
-> "stream_cif_mipi_id1":0 []
-> "stream_cif_mipi_id2":0 []
-> "stream_cif_mipi_id3":0 []
-> "rkcif_scale_ch0":0 [ENABLED]
-> "rkcif_scale_ch1":0 []
-> "rkcif_scale_ch2":0 []
-> "rkcif_scale_ch3":0 []
-> "rkcif_tools_id0":0 []
-> "rkcif_tools_id1":0 []
-> "rkcif_tools_id2":0 []
pad6: Source
-> "stream_cif_mipi_id0":0 []
-> "stream_cif_mipi_id1":0 []
-> "stream_cif_mipi_id2":0 []
-> "stream_cif_mipi_id3":0 []
-> "rkcif_scale_ch0":0 []
-> "rkcif_scale_ch1":0 [ENABLED]
-> "rkcif_scale_ch2":0 []
-> "rkcif_scale_ch3":0 []
-> "rkcif_tools_id0":0 []
-> "rkcif_tools_id1":0 []
-> "rkcif_tools_id2":0 []
pad7: Source
-> "stream_cif_mipi_id0":0 []
-> "stream_cif_mipi_id1":0 []
-> "stream_cif_mipi_id2":0 []
-> "stream_cif_mipi_id3":0 []
-> "rkcif_scale_ch0":0 []
-> "rkcif_scale_ch1":0 []
-> "rkcif_scale_ch2":0 [ENABLED]
-> "rkcif_scale_ch3":0 []
-> "rkcif_tools_id0":0 []
-> "rkcif_tools_id1":0 []
-> "rkcif_tools_id2":0 []
pad8: Source
-> "stream_cif_mipi_id0":0 []
-> "stream_cif_mipi_id1":0 []
-> "stream_cif_mipi_id2":0 []
-> "stream_cif_mipi_id3":0 []
-> "rkcif_scale_ch0":0 []
-> "rkcif_scale_ch1":0 []
-> "rkcif_scale_ch2":0 []
-> "rkcif_scale_ch3":0 [ENABLED]
-> "rkcif_tools_id0":0 []
-> "rkcif_tools_id1":0 []
-> "rkcif_tools_id2":0 []
pad9: Source
-> "stream_cif_mipi_id0":0 []
-> "stream_cif_mipi_id1":0 []
-> "stream_cif_mipi_id2":0 []
-> "stream_cif_mipi_id3":0 []
-> "rkcif_scale_ch0":0 []
-> "rkcif_scale_ch1":0 []
-> "rkcif_scale_ch2":0 []
-> "rkcif_scale_ch3":0 []
-> "rkcif_tools_id0":0 [ENABLED]
-> "rkcif_tools_id1":0 []
-> "rkcif_tools_id2":0 []
pad10: Source
-> "stream_cif_mipi_id0":0 []
-> "stream_cif_mipi_id1":0 []
-> "stream_cif_mipi_id2":0 []
-> "stream_cif_mipi_id3":0 []
-> "rkcif_scale_ch0":0 []
-> "rkcif_scale_ch1":0 []
-> "rkcif_scale_ch2":0 []
-> "rkcif_scale_ch3":0 []
-> "rkcif_tools_id0":0 []
-> "rkcif_tools_id1":0 [ENABLED]
-> "rkcif_tools_id2":0 []
pad11: Source
-> "stream_cif_mipi_id0":0 []
-> "stream_cif_mipi_id1":0 []
-> "stream_cif_mipi_id2":0 []
-> "stream_cif_mipi_id3":0 []
-> "rkcif_scale_ch0":0 []
-> "rkcif_scale_ch1":0 []
-> "rkcif_scale_ch2":0 []
-> "rkcif_scale_ch3":0 []
-> "rkcif_tools_id0":0 []
-> "rkcif_tools_id1":0 []
-> "rkcif_tools_id2":0 [ENABLED]
- entity 58: rockchip-csi2-dphy0 (2 pads, 2 links)
type V4L2 subdev subtype Unknown flags 0
device node name /dev/v4l-subdev1
pad0: Sink
[fmt:SGBRG10_1X10/3864x2192@10000/300000 field:none
crop.bounds:(12,16)/3840x2160]
<- "m00_b_imx415 3-001a":0 [ENABLED]
pad1: Source
-> "rockchip-mipi-csi2":0 [ENABLED]
- entity 63: m00_b_imx415 3-001a (1 pad, 1 link)
type V4L2 subdev subtype Sensor flags 0
device node name /dev/v4l-subdev2
pad0: Source
[fmt:SGBRG10_1X10/3864x2192@10000/300000 field:none
crop.bounds:(12,16)/3840x2160]
-> "rockchip-csi2-dphy0":0 [ENABLED]
从entity 63信息中可以看到：
该Entity完整的名称是：m00_b_imx415 3-001a
它是一个V4L2 subdev(Sub-Device) Sensor
它对应的节点是 /dev/v4l-subdev2，应用程序（如v4l2-ctl）可以打开它，并进行配置
它仅有一个输出（Source）节点，记为pad0
它的输出格式是 [fmt:SGBRG10_1X10/3864x2192@10000/300000 field:none
crop.bounds:(12,16)/3840x2160]，其中SBGGR10是一种mbus-code的简称
它的Source pad0 链接到"rockchip-csi2-dphy0"的pad0，并且当前的状态是 ENABLED。
media-ctl -d /dev/media1 -p
- entity 6: rkisp_mainpath (1 pad, 1 link)
type Node subtype V4L flags 0
device node name /dev/video11
pad0: Sink
<- "rkisp-isp-subdev":2 [ENABLED]
使用
gst-launch-1.0 v4l2src device=/dev/video11 ! video/x-raw,format=NV12,width=3840,height=2160, framerate=30/1 ! xvimagesink
GivenIamadumbprogrammerandIamusingrspecandIamusingsporkandIwanttodebug...mmm...let'ssaaay,aspecforPhone.那么，我应该把“require'ruby-debug'”行放在哪里，以便在phone_spec.rb的特定点停止处理？(我所要求的只是一个大而粗的箭头，即使是一个有挑战性的程序员也能看到:-3)我已经尝试了很多位置，除非我没有正确测试它们，否则会发生一些奇怪的事情:在spec_helper.rb中的以下位置:require'rubygems'require'spork'
使用Ruby1.9.2运行IDE提示说需要gemruby-debug-base19x并提供安装它。但是，在尝试安装它时会显示消息Failedtoinstallgems.Followinggemswerenotinstalled:C:/ProgramFiles(x86)/JetBrains/RubyMine3.2.4/rb/gems/ruby-debug-base19x-0.11.30.pre2.gem:Errorinstallingruby-debug-base19x-0.11.30.pre2.gem:The'linecache19'nativegemrequiresinstall
我有:When/^(?:|I)follow"([^"]*)"(?:within"([^"]*)")?$/do|link,selector|with_scope(selector)doclick_link(link)endend我打电话的地方:Background:GivenIamanexistingadminuserWhenIfollow"CLIENTS"我的HTML是这样的:CLIENTS我一直收到这个错误:.F-.F--U-----U(::)failedsteps(::)nolinkwithtitle,idortext'CLIENTS'found(Capybara::Element
Ruby是否有逐步调试器，类似于Perl的“perl-d”？ 最佳答案 ruby-debug(对于ruby1.8)，debugger(对于ruby1.9)，byebug(对于ruby2.0)以及trepanning系列都有一个-x或--trace选项。在调试器内部，命令setlinetrace将打开或关闭线路跟踪。这是themanualforruby-debug原来的答案已经修改，因为数据噪声文章的链接，唉，不再有效了。还添加了ruby-debug的后继者 关于ruby-Ruby
文章目录一、项目场景二、基本模块原理与调试方法分析——信源部分：三、信号处理部分和显示部分：四、基本的通信链路搭建：四、特殊模块：interpretedMATLABfunction：五、总结和坑点提醒一、项目场景 最近一个任务是使用simulink搭建一个MIMO串扰消除的链路，并用实际收到的数据进行测试，在搭建的过程中也遇到了不少的问题（当然这比vivado里面的debug好不知道多少倍）。准备趁着这个机会，先以一个很基本的通信链路对simulink基础和相关的debug方法进行总结。 在本篇中，主要记录simulink的基本原理和基本的SISO通信传输链路（QPSK方式），计划在下篇记
我已经开始使用RubyMine6。我正在处理Rails4、Ruby2.1.1项目。我无法找到如何使用Pow作为服务器调试到RubyMine。你能给我指明正确的方向吗？ 最佳答案 我能够使用远程调试从RubyMine进行调试。我正在使用RubyMine6、Rails3、Ruby2.1.1。首先创建一个.powenv文件并添加:exportRUBY_DEBUG_PORT=1234exportPOW_WORKERS=1将以下gem添加到您的Gemfile:gem'ruby-debug-ide'gem'debase'创建一个新的初始化器st
当我编写代码时，我非常频繁地使用“puts”语句进行调试。它允许我查看服务器中发生的情况。在调试代码的时候，不知道是什么原因，我把这些“puts”语句去掉了。这是个好主意还是我应该保留它们以使我的服务器日志更加清晰？ 最佳答案 您应该使用记录器而不是puts。使用这种语句:Rails.logger.debug"DEBUG:#{self.inspect}#{caller(0).first}"ifRails.logger.debug?如果您想(几乎)实时查看调试，只需在另一个终端窗口中使用tail命令:tail-Flog/develop
我试图在我的RubyonRails应用程序中调试一个极其缓慢的请求调用。我已设法根据自己的喜好优化Controller方法，Rails的日志告诉我它已在XX毫秒内完成操作(Completed200OKin5049ms(Views:34.9ms|ActiveRecord:76.3ms)).但是，在加载页面时，在浏览器中实际呈现任何内容之前打印此消息很长；最多约15秒的等待时间。Rackmini-profiler证实了这一点，告诉我GET操作(不计算完成Controller操作所花费的时间)花费了14秒左右。(分析器还确认Controller操作的执行时间约为5秒)。我可以接受Contro
假设我在调试时停在了点上:defget_databyebug=>@cache||=calculate_dataend而@cache有值，所以step函数calculate_data不会被执行。但是我需要在这个确切的运行时点检查calculate_data内部发生了什么。我可以只执行calculate_data并在控制台输出中查看其结果，但是我可以从调试控制台执行函数并同时进入它？(使用byebug或其他一些调试工具)。目标-是在任意时间检查calculate_data逻辑，特别是当get_data调用时@cache已填充。 最佳答案
这是一个长期存在的挫败感来源，但也许我遗漏了什么。如果我正在调试，并且我想退出调试器并返回到IRB或Rails控制台，“退出”将不起作用，因为它将退出IRB。“完成”似乎也与继续具有相同的效果。使用“删除”删除断点然后尝试“继续”或“完成”不起作用。有什么想法吗？ 最佳答案 至少在byebug中，你可以这样做:evalreturn它具有计算当前函数的return语句的净效果。这有时会奏效，具体取决于调用堆栈的外观。现在虽然这不会删除当前断点....如果您只是想收回控制权，在大多数情况下这会做到这一点，具体取决于您的代码结构。在您的代